Wiring diagram | Johnson Outboard Tachometer Wiring
Johnson Outboard Tachometer Wiring | A wiring diagram is a simplified conventional pictorial representation of an electrical circuit. It shows the components of the circuit as simplified shapes, and the power and signal connections between the devices.
Johnson Outboard Tachometer Wiring | A wiring diagram usually gives information about the relative position and arrangement of devices and terminals on the devices, to help in building or servicing the device. Johnson Outboard Tachometer Wiring This is unlike a schematic diagram, where the arrangement of the components' interconnections on the diagram usually does not correspond to the components' physical locations in the finished device. A pictorial diagram would show more detail of the physical appearance, whereas a wiring diagram uses a more symbolic notation to emphasize interconnections over physical appearance.
Johnson Outboard Tachometer Wiring A wiring diagram is often used to troubleshoot problems and to make sure that all the connections have been made and that everything is present.
Architectural wiring diagrams | Johnson Outboard Tachometer Wiring
Architectural wiring diagrams show the approximate locations and interconnections of receptacles, lighting, and permanent electrical services in a building. Interconnecting wire routes may be shown approximately, where particular receptacles or fixtures must be on a common circuit.
Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol.
Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the Panel Surya board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
A set of wiring diagrams may be required by the electrical inspection authority to approve connection of the residence to the public electrical supply system.
Wiring diagrams will also include panel schedules for circuit breaker panelboards, and riser diagrams for special services such as fire alarm or closed circuit television or other special services.
Schematic | Johnson Outboard Tachometer Wiring
A schematic, or schematic diagram, is a representation of the elements of a system using abstract, graphic symbols rather than realistic pictures. A schematic usually omits all details that are not relevant to the key information the schematic is intended to convey, and may include oversimplified elements in order to make this essential meaning easier to grasp. For example, a subway map intended for passengers may represent a subway station with a dot.
The dot is not intended to resemble the actual station at all; instead, it aims to give the viewer information without unnecessary visual clutter. A schematic diagram of a chemical process uses symbols in place of detailed representations of the vessels, piping, valves, pumps, and other equipment that compose the system; in so doing, it emphasizes the functions of these individual elements and the interconnections among them--and suppresses their particular physical details.
In an electronic circuit diagram, the layout of the symbols may not look anything like the circuit as it appears in the physical world: instead of representing the way the circuit looks, the schematic aims to capture, on a more general level, the way it works.
Electrical and electronic industry
Johnson Outboard Tachometer Wiring | In electrical and electronic industry, a schematic diagram is often used to describe the design of equipment. Schematic diagrams are often used for the maintenance and repair of electronic and electromechanical systems. Original schematics were done by hand, using standardized templates or pre-printed adhesive symbols, but today electronic design automation software (EDA or "electrical CAD") is often used.
Johnson Outboard Tachometer Wiring | In electronic design automation, until the 1980s schematics were virtually the only formal representation for circuits. More recently, with the progress of computer technology, other representations were introduced and specialized computer languages were developed, since with the explosive growth of the complexity of electronic circuits, traditional schematics are becoming less practical. For example, hardware description languages are indispensable for modern digital circuit design.
Schematics for electronic circuits are prepared by designers using EDA (electronic design automation) tools called schematic capture tools or schematic entry tools. These tools go beyond simple drawing of devices and connections. Usually they are integrated into the whole IC design flow and linked to other EDA tools for verification and simulation of the circuit under design.
Johnson Outboard Tachometer Wiring | In electric power systems design, a schematic drawing called a one-line diagram is frequently used to represent substations, distribution systems or even whole electrical power grids. These diagrams simplify and compress the details that would be repeated on each phase of a three-phase system, showing only one element instead of three. Electrical diagrams for switchgear often have common device functions designate by standard function numbers.